IC Series Inverter/Charger: FINAL INSPECTION
# Steps on Final Inspection 1. Verify all cables/conduit runs are secured with zip ties or other non- conductive cable clamps to prevent damage from vibration. 2. Ensure all cables that pass-through walls, bulkheads, or any other openings are protected against abrasion by using strain reliefs and/or grommets. 3. Ch…
IC Series Inverter/Charger: REQUIRED TOOLS AND MATERIALS
**Required Tools ** a. 13mm or adjustable wrench b. Screwdriver (Phillips & Flathead) c. Wire strippers and cutters d. Electric hand drill and drill bits Optional Tools e. Keyhole saw f. Pencil or marker g. Pliers h. Caulking gun i. Sealant j. Digital multimeter k. Torque driver l. Butt splice crimping too…
IC Series Inverter/Charger: UNIT DIMENSIONS
![][1] ![][2] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/02-18/86038789-2e14-402c-b0d4-7b0c0ec48509/IC%20dims%20top.jpg [2]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/02-18/476a8c79-cf72-45c6-8c69-a82351e6f70e/IC%20dims%20side.jpg
IC Series Inverter Charger: GENERAL INFORMATION
# 2.1 CAUTIONS/WARNINGS This document contains important safety instructions for the products produced by Go Power! Read all instructions and cautionary markings on the product and on any accessories or additional equipment included in the installation. Failure to follow these instructions could result in severe shoc…
IC Series Inverter/Charger: MOUNTING THE INVERTER/CHARGER
# HOW TO MOUNT THE INVERTER/CHARGER Before connecting any wires to the Inverter/Charger the unit must be mounted securely in a location which meets the requirements detailed in section 3.2. The GP-IC-2000 weighs: 39 lbs (17.6kg). The GP-IC-3000 weighs: 52lbs (23.6kg). Take the necessary precautions required whilst l…
IC Series Inverter/Charger: WARNING LABELS
# WARNING LABELS When an Inverter/Charger is installed in a building the National Electrical Code (NEC) requires a label or plaque to be provided. This label/plaque is required to be easily visible and to inform users of the location of all electrical system disconnects. Buildings with stand-alone power systems (sola…
IC Series Inverter/Charger: UNIT ACCESSORIES
The IC Series Inverter/Charger has two accessories available: * IC Series remote (not included). * Battery temperature sensor (included). **IC Series Remote** This remote control device can be used for monitoring the performance of the unit. It is also used to program certain settings on the Inverter, Charger,…
IC Series Inverter Charger: DC CABLE CONNECTIONS
# DC CABLE CONNECTIONS DIAGRAMS When installing the battery cable ring lug onto the Inverter/Charger DC terminal and the battery post, do not put anything between the ring lug and the metal surface. Incorrectly installed hardware causes a high resistance connection which could lead to poor Inverter/Charger performanc…
IC Series Inverter/Charger: PREPARING THE DC CABLES
# PREPARING THE DC CABLES Go Power! supplies 2 ring lugs with the IC Series, which can be used for the Inverter/Charger end of the DC Cables. Source the correct ring terminals for the batteries you are using. * Cut the negative and positive cables to the required length. * Strip off enough insulation so you can …
IC Series Inverter/Charger: BATTERY BANK CONFIGURATIONS
![][1] ![][2] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/e9037356-bab6-4114-94b3-2b662d2bcf5d/battery%20wire.jpg [2]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/4a1d74d2-9931-4a5b-9d4f-424e1ff45f2b/battery%20wire%202.jpg
