IC Series Inverter/Charger: REQUIRED TOOLS AND MATERIALS
**Required Tools ** a. 13mm or adjustable wrench b. Screwdriver (Phillips & Flathead) c. Wire strippers and cutters d. Electric hand drill and drill bits Optional Tools e. Keyhole saw f. Pencil or marker g. Pliers h. Caulking gun i. Sealant j. Digital multimeter k. Torque driver l. Butt splice crimping too…
IC Series Inverter/Charger: UNIT DIMENSIONS
![][1] ![][2] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/02-18/86038789-2e14-402c-b0d4-7b0c0ec48509/IC%20dims%20top.jpg [2]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/02-18/476a8c79-cf72-45c6-8c69-a82351e6f70e/IC%20dims%20side.jpg
IC Series Inverter Charger: DC CABLE CONNECTIONS
# DC CABLE CONNECTIONS DIAGRAMS When installing the battery cable ring lug onto the Inverter/Charger DC terminal and the battery post, do not put anything between the ring lug and the metal surface. Incorrectly installed hardware causes a high resistance connection which could lead to poor Inverter/Charger performanc…
IC Series Inverter/Charger: UNIT ACCESSORIES
The IC Series Inverter/Charger has two accessories available: * IC Series remote (not included). * Battery temperature sensor (included). **IC Series Remote** This remote control device can be used for monitoring the performance of the unit. It is also used to program certain settings on the Inverter, Charger,…
IC Series Inverter/Charger: BATTERY BANK CONFIGURATIONS
![][1] ![][2] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/e9037356-bab6-4114-94b3-2b662d2bcf5d/battery%20wire.jpg [2]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-06/4a1d74d2-9931-4a5b-9d4f-424e1ff45f2b/battery%20wire%202.jpg
IC Series Inverter/Charger: PREPARING THE DC CABLES
# PREPARING THE DC CABLES Go Power! supplies 2 ring lugs with the IC Series, which can be used for the Inverter/Charger end of the DC Cables. Source the correct ring terminals for the batteries you are using. * Cut the negative and positive cables to the required length. * Strip off enough insulation so you can …
IC Series Inverter/Charger: AC WIRE SIZE AND OVERCURRENT PROTECTION
# AC WIRE SIZE AND OVERCURRENT PROTECTION The wires used for the Input AC and Output AC must be sized to meet local electrical safety requirements. The AC wiring must be protected from short circuits and overloads by an overcurrent protection device. These requirements are usually met using a main panel and sub panel…
IC Series Inverter/Charger: GROUNDING ON BOATS
# Grounding Information If you are installing the IC Series Inverter/Charger on a boat there are some specific guidelines/standards to follow. The Inverter/Charger must be installed adhering to the standards of the ABYC (American Boat and Yacht Council). Some guidelines are outlined below but these notes do not repla…
IC Series Inverter/Charger: AC POWER SOURCE TYPES
# TYPES OF AC POWER SOURCE AC Input power to the IC Series can be supplied from a split-phase or dual- input single phase AC source. These sources typically include utility power or a generator. • **Split Phase**: This source has 4 lines: 2 Hot Lines, one neutral and one ground. The 2 hot lines are 120VAC and are 18…
IC Series Inverter/Charger: GFCI (GROUND FAULT CIRCUIT INTERRUPTION) OUTLETS
# GFCI (GROUND FAULT CIRCUIT INTERRUPTION) OUTLETS SPECIFICATION Compliance with UL standards requires that Go Power! test and recommend specific GFCIs for use on the AC output of the IC Series. GFCIs shall be installed in the AC output wiring system to proceed all branch circuits. A GFCI is a device that de-energiz…
