IC Series Inverter/Charger: INVERTING MODE
In inverting mode: * The load power required by the appliances (fridge, TV, charger) is 2000W (16.7AAC x 120VAC) - 1. * The inverter supplies the 2000W or 3000W (186 ADC x 12VDC x 0.9) of AC power required to power the appliances - 2. * Shore power (utility or generator) is not connected. ![][1] [1]: https…
IC Series Inverter/Charger: AC WIRE SIZE AND OVERCURRENT PROTECTION
# AC WIRE SIZE AND OVERCURRENT PROTECTION The wires used for the Input AC and Output AC must be sized to meet local electrical safety requirements. The AC wiring must be protected from short circuits and overloads by an overcurrent protection device. These requirements are usually met using a main panel and sub panel…
IC Series Inverter/Charger: AC POWER SOURCE TYPES
# TYPES OF AC POWER SOURCE AC Input power to the IC Series can be supplied from a split-phase or dual- input single phase AC source. These sources typically include utility power or a generator. • **Split Phase**: This source has 4 lines: 2 Hot Lines, one neutral and one ground. The 2 hot lines are 120VAC and are 18…
IC Series Inverter/Charger: DC WIRE SIZING
# DC WIRE SIZING SPECIFICATIONS The distance between the battery bank and the Inverter/Charger should be as short as possible to achieve maximum efficiency and to reduce fire hazards. The cables should be as short as possible and the overall length of both cables added together should be less than 10 ft (3m) to compl…
Go Power! Products : RECYCLING INFO
Congratulations on purchasing your Go Power! IC Series Inverter/Charger. The IC Series Inverter/Charger combines the functions of a pure sine wave inverter, battery charger and AC transfer switch into one unit - saving space, installation time, and system complexity. The IC Series is designed for mobile and home power…
IC Series Inverter/Charger: LOCATION AND ENVIRONMENTAL REQUIREMENTS
# LOCATION AND ENVIRONMENTAL REQUIREMENTS The IC Series Inverter/Charger must be installed in a location that meets the following requirements: **1. TEMPERATURE** Make sure the Inverter/Charger is installed in a location where the normal air temperature is between 0 °C and 50 °C. The cooler the better within this …
IC Series Inverter/Charger: AC WIRING 3 - Split Phase, 50A Service, Dual IN, Dual OUT, Option 1 [No Sub Panel]
![][1] [1]: https://hf-files-oregon.s3.amazonaws.com/hdpgopower_kb_attachments/2020/05-08/02d8380a-0a80-4206-ab8f-978a0bde8611/wire%203.jpg
IC Series Inverter/Charger: AC WIRING
# AC WIRING INSTRUCTIONS The AC cables link the Inverter/Charger to the main panel and the sub panel. These cables handle the incoming alternating current (AC) utility or generator power, which can be passed through the Inverter/Charger to directly power the main appliances (pass-through mode) and/or used to charge t…
IC Series Inverter/Charger: FACTORY DEFAULT VALUES
# FACTORY DEFAULT VALUES The IC Series Inverter/Charger uses default values for the following adjustable settings: ![][1] These settings are only adjustable with the GP-ICR-50 remote, which can be purchased separately from Go Power!. For detailed information on these settings please refer to the remote control man…
IC Series Inverter/Charger: POWER SHARING MODE 1
# POWER SHARING MODE In power sharing mode: * The power required by the appliances (fridge, TV, charger) is 4200W (35AAC x 120VAC) - 1. * Shore power (Utility or Generator) is connected and supplying 6000W (50AAC x 120VAC) - 2. * 4200W of AC power is passed through OUT 1 on the Inverter/Charger to power the ap…
